Product DescriptionFeatures: - Input Voltage: AC 100-240V 50/60Hz – Output: DC 5.0V 2500mA (2.5A) – Cable Length: Approx.110 cm – Short Circuit Protection – Overload Protection – Consistent fixed switching voltage – Internal Fuse for Extra Safety – With Power Switch, Easy to turn on and off – Weight: ..

Product DescriptionFeatures: 1. With switch ON/OFF, easy to turn on or turn off 2. Can load power at DC 5V/2A stably 3. USB / Micro USB interface 4. Perfectly matched to Raspberry PI or Banana Pi 5. Wire is made of copper 6. Wrapping is made of PVC Specifications: Length: 150cm Wire size: 3.4mm in diameter Net weight: 40g N..

Product DescriptionFeature: Power supply: 9V-12V (Recommended 9V laminated battery) Antenna: 50 ohm, unbalanced Frequency range: transmitter local oscillator frequency: 7023kHz; receive local oscillator frequency: about 7023-7026KHz Headphones: low-impedance headphones Transmit power: 0.8W (using a 9V power supply), 1.2W (12V power supply) Suppress..

Product DescriptionFeatures: - Input Voltage: AC 100-240V 50/60Hz – Output: DC 5.0V 2500mA (2.5A) – Cable Length: Approx.110 cm – Short Circuit Protection – Overload Protection – Consistent fixed switching voltage – Internal Fuse for Extra Safety – With Power Switch, Easy to turn on and off – Weight: ..

Product DescriptionFeature: Power supply: 9V-12V (Recommended 9V laminated battery) Antenna: 50 ohm, unbalanced Frequency range: transmitter local oscillator frequency: 7023kHz; receive local oscillator frequency: about 7023-7026KHz Headphones: low-impedance headphones Transmit power: 0.8W (using a 9V power supply), 1.2W (12V power supply) Suppress..

Product DescriptionFeature: Multifunction GPIO Extension Board For Raspberry Pi 2/3/model B / Orange Pi PC DIY Demo Board / Banana Pi Package includes: 1 x GPIO Extension Board Note:(Raspberry Pi is not included)..

Product DescriptionDescription:This camera is compatible with any version of Raspberry Pi.You can adjust it based on the distance.Features:5 million pixelsOV5647 sensor chipCamera parameters:CCD Size: 1/4 inchAperture (F): 1.8Focal length (Focal Length): 3.6mm (adjustable)Viewing angle (Diagonal): 75.7 degreesBest sensor pixels: 1080p4 screw holes:..

Product DescriptionFeature: Power supply: 9V-12V (Recommended 9V laminated battery) Antenna: 50 ohm, unbalanced Frequency range: transmitter local oscillator frequency: 7023kHz; receive local oscillator frequency: about 7023-7026KHz Headphones: low-impedance headphones Transmit power: 0.8W (using a 9V power supply), 1.2W (12V power supply) Suppress..

Product DescriptionFeature: Compatible with Arduino Mega 2560 board. Built on the ATmega2560 microcontroller and USB-UART interface chip CH340G. Board for functionality similar to the Arduino Mega 2560. It is a budget, but the same stable, and uses the original chips ATmega2560 (16 MHz). The board used the chip CH340G as converter UART-USB. Chip CH..

Product DescriptionFeatures: The hole gap is 2.54mm, and it's compatible with IC with DIP package. The IO port can be quickly and easily implement your ideas. Note: The Raspberry Pi mainboard is not included. Package included: 3 x Prototyping Shield..

Product DescriptionFeatures: The hole gap is 2.54mm, and it's compatible with IC with DIP package. The IO port can be quickly and easily implement your ideas. Note: The Raspberry Pi mainboard is not included. Package included: 5 x Prototyping Shield..

Product DescriptionDescription: OPS-1 light control switch has two trigger modes and two output modes: 1). Set trigger mode by JMP1: Light trigger mode (1-3): When the photosensitive resistance induction to the outside light from the matt to light or light gradually increased, the relay pull. Dark trigger mode (2-4): When the photosensitive resista..

Product DescriptionFeatures: The hole gap is 2.54mm, and it's compatible with IC with DIP package. The IO port can be quickly and easily implement your ideas. Note: The Raspberry Pi mainboard is not included. Package included: 10 x Prototyping Shield..

Product DescriptionDescription: OPS-1 light control switch has two trigger modes and two output modes: 1). Set trigger mode by JMP1: Light trigger mode (1-3): When the photosensitive resistance induction to the outside light from the matt to light or light gradually increased, the relay pull. Dark trigger mode (2-4): When the photosensitive resista..

Product DescriptionFeatures: - Input: AC 100V-240V 50/60HZ; – Output: 5V Max 3A; – DC Plug: 4.0mm x 1.7mm – EU Plug Note: Most of orange pi board use the 4.0×1.7mm DC plug; but some orange pi board use the micro usb plug (such as Orange Pi zero use micro USB plug) Package included: 1 x Power Adapter..